Home > Hampton Bay > Hampton Bay Ceiling Fan Not Working

Hampton Bay Ceiling Fan Not Working

Contents

Reply James May 9, 2015 at 6:36 pm # Hi Bob. Verify the electricity is off by operating the light switch and verifying with a voltage tester. Not sure if this is an overload issue, but replaced with incandescent and immediately worked properly. April 3, 2016 at 1:27 am Del Mar Fans & Lighting Hi Leslie, If your ceiling fan is usually ran from a wall or remote control once you click the ceiling http://sistemainmo.com/hampton-bay/hampton-bay-ceiling-fan-dimmer-not-working.php

We hope this helps! I hope I have helped you out in your situation, and please let us know if you have any further questions.

aboveaveragejoe

Best Answer Best The fan blades will turn in the opposite direction and reverse airflow. Please contact us if we can help! http://www.hamptonbay-ceilingfans.com/hampton-bay-ceiling-fan-troubleshooting/

Hampton Bay Ceiling Fan Light Not Working

After I installl the blades no spinning occurs, even though I can hear the motor working. For no reason that I can discern, the fan stopped working and the lights are very dim. Ugg! Restore the power and resume normal operation.

October 22, 2015 at 12:27 pm Joanne Ladd The pull chain for the blades appear to be stuck . November 12, 2014 at 7:17 am Del Mar Fans & Lighting Hi Paul, Unfortunately, we don't know of any local retailers in Mar Del Plata that sell ceiling fan capacitors. I have bypassed the receiver of the Altura receiver with same result. Hampton Bay Receiver Any suggestions?

I moved the fan to a different bedroom & now the motor kinda has a hum to it which was not there before it was moved. Hampton Bay Ceiling Fan Dip Switch Location Sometimes the reverse switch is just far enough to not make the connection needed. If you buy that capacitor, connect only the 1.2uF wire as before and cap the 2.3uF wire with a wire nut for a no-connection. See "Why did my run capacitor fail?" for more info.

The lights work, but after I turned it on, one bulb went out. Hampton Bay Ceiling Fan Not Working Light Works The electrical source for this fan also feeds a 2 - way switch for our hallway light. If so, discontinue use of the heater and have a qualified electrician check and/or replace the faulty outlet(s). However, it blows my mind how we can even have such problems these days.

Hampton Bay Ceiling Fan Dip Switch Location

To check your product specifications, please refer to your product manual.

It would've been nice if the owner's manual has what wattage bulb it needs. Hampton Bay Ceiling Fan Light Not Working Since it seems like both the lights and fan failed at the same time it is likely that the wiring failure could be in this common return line. Reset Hampton Bay Ceiling Fan Remote I have 2 Honeywell model #10209, tri-mount, 4 speed ceiling fans.

The battery has been changed but it still doesn't work. this page The cool, stagnant air begins to circulate when the ceiling fan turns on and your sweat begins to evaporate giving you a cooling sensation. Please note: These parts may or may not work for your specific product. Blades turn so motor not frozen. Hampton Bay Universal Remote

Back to Fireplace What happens if I receive my product and it's damaged? Try direct wiring your fan: If your dip switches on the remote match your receiver and your remote lights up properly, the receiver may need to be replaced. October 6, 2014 at 4:47 pm Deborah Mauldin Del Mar Fans & LightingWELL I AM NO ROCKET SCIENTIST, BUT I KNOW I AM NOT STUPID. get redirected here Are the fans connected to a dimmer switch?

iScaper1 532,899 views 18:28 Replacing a broken pull chain switch on a ceiling fan. - Duration: 7:55. Hampton Bay Ceiling Fans Manual Turn the power off the circuit breaker. The capacitor might last much much longer but that's all it was tested for.

share|improve this answer answered May 30 '13 at 8:26 Michael Karas 27.6k42152 I've fixed a couple where wiggling wires inside the fan housing simply came loose from their connections.

If your light kit is spinning, but the fan blades are not, this could indicate a faulty wiring issue. Ensure the hanger ball has been "seated" into the groove slot of the hanger bracket. If your set includes cushions or mesh fabric, you may use scotch guard to protect them. Hampton Bay Ceiling Fans Wiring Diagram essortment 98,831 views 4:32 Loading more suggestions...

Check that the dip switches on the remote and receiver are set to the same frequency. I have a ceiling fan with lights on a dimmer switch. The high speed fan setting may be wired in several ways: * High speed setting bypasses the capacitor. useful reference The capacitor markings must be readable.

My son took it apart and did not mark the wiring. x Get Help from Bob Vila Give-Aways & Offers Monthly Must Do's DIY Project Ideas Step-by-Step Guides Inspirational Photo Galleries Thanks! powered by Olark live chat software Professional? • About Us • Contact Us • HoursMon - Thu: 8AM - 8PM EST,Fri: 8AM - 6PM EST,Sat: 10AM - 4PM EST,Sun: 10AM - It seems most consumer ceiling fan capacitors are Class B rated for 10,000 hours. 1 year equals 8765.81 hours but this isn't to state a Class B CBB61 capacitor will only

I went through the Home Depot number you gave above and they hooked me in with a King of Fans technician. Be well! The capacitor case was ruptured with gobs of hard gray plastic swelled out. Because it has attracted low-quality or spam answers that had to be removed, posting an answer now requires 10 reputation on this site (the association bonus does not count).

Order a Replacement Ceiling Fan Motor Capacitor You will need the ceiling fan Model Number or UPC # to order replacement parts from Home Depot / Hampton Bay Customer Support as If your ceiling fan is running slow on all speeds, we recommend replacing the capacitor on the fan. I'd try dimmable LED lights first, if that doesn't solve the flickering you can always return them. Can I install my Hampton Bay bath fans above a tub and a shower?

It makes an awful noise and I have to turn it off immediately. the fan works but not the light. Confirm the canopy is not touching the ceiling while the fan is in operation. They are not visibly damaged.

How can I fix this myself without having to call an electrician or someone to help? You can try bypassing the receiver and direct wiring your fan to see if that addresses your issue. Low profile design is nice, but defnitely limits utility.

Hope this helps and good luck

(don't know the model off-hand since diagnosed problem already)

Best Answer Best Answer Best Answer Like Sign in Statistics 440 views 0 Like this video?

If the motor itself isn't working(sound but no movement) your next step would be contacting the manufacturer to see about specific troubleshooting.