Home > Hampton Bay > Hampton Bay Ceiling Fan Remote Receiver Not Working

Hampton Bay Ceiling Fan Remote Receiver Not Working

Contents

MiamisonMar 30, 2005, 09:35 AMundefined One thing you might check is the frequency selection dip switch. Check the wiring - Try turning off the power at your breaker box and then uninstalling your light fixture to check the connections between the junction box (house supply wires) and It is a 4-bladed fan that is part of the "Romano" by hampton bay series model 360-424. Is the receiver difficult to replace and why can;t they send out the part for free as this seems to be a defect in the design.

Thanks

Lori

Best Answer Best my review here

Heaters draw more current than small appliances, overheating of the outlet may occur even if it has not occurred with the use of other appliances. Why does my Hampton Bay fan turn on and off by itself? For instructions on identifying your SKU, UPC and/or model number, please click here. Slide the dip switches to your choice of either up or down. read this article

Hampton Bay Ceiling Fan Dip Switch Location

Back to Patio Furniture How should I clean and protect my patio set? Be sure the plug fits tight in the outlet. If the lights have separate leads, you can do the same thing, or just go with a simple on/off for all or nothing.

Watch QueueQueueWatch QueueQueue Remove allDisconnect Loading... Then, rotate the fan until the next blade is positioned for measurement. Is the receiver difficult to replace and why can;t they send out the part for free as this seems to be a defect in the design.ThanksLori

Hi,

I am actually a designer Hampton Bay Ceiling Fan Remote Manual I have a Hampton Bay model # 71607/ sku# 1000507127.

I have changed the batteries on my remote and it seems to work fine.

Please contact Hampton Bay for assistance. Hampton Bay Universal Remote Sign in to make your opinion count. Thank you for all your help. Any ideas?

Someone else told me about the dip swithches. Hampton Bay Ceiling Fan Remote App Batteries in the remote control are good and the red light on the remote control lights up when any of the buttons are pushed. Never use abrasive cleansers, liquid sprays, or any cleaner that could scratch the surface. Try a balancing kit: If your fan is still wobbling, please use the enclosed blade balancing kit.

Hampton Bay Universal Remote

For those of you who, like me have failed Windward III's, the UPC codes are 082392551568 for the white version and 082392551575 for the brushed steel version. http://www.homedepot.com/c/SPC_BRD_HamptonBay_Help The appropriate speed setting for warm or cool weather depends on factors such as the room size, ceiling height, and number of fans. Hampton Bay Ceiling Fan Dip Switch Location Simply visit www.homedepot.com and search for your product UPC or model number and select your fan.The UPC (12-digits) and/or model number can be found on the following: The product box Your Hampton Bay Receiver Some motors only have 2 coils (start and run, we'll call them) and the speeds are not determined by coil taps but by capacitors.

Sign in 9 16 Don't like this video? this page When in doubt, please consult an electrician or contact Hampton Bay Customer Service. My fan is noisy. rbjDec 12, 2005, 11:12 AMOne thing you might check is the frequency selection dip switch. Hampton Bay Remote Replacement

Then select Product Overview and click on Warranty under "Info and Guides."For instructions on identifying your model or UPC number, please click here. Since we are pretty sure that its the receiver, they are usually installed at the factory between the motor housing and light kit which means sometimes entire replacement of the fan.:mansad: Back to Lighting Why is my light flickering on my light fixture? get redirected here Press the remote control buttons with an even motion and gentle pressure.

I talked to Hampton Bay and King of Fans today and they said it sounded like not the remote but the switch inside the fan. Hampton Bay Ceiling Fan Manual atrobinsonFeb 28, 2006, 01:04 AMI took the light fixture off and used the volt meter on the part that was off to make sure the wires carried a current. The light switches on but when I try to control the light intensity it just blinks.

The control module, totally crispy-crittered.

WARRANTY INFORMATION Warranty Policy What happens if I receive my product and it's damaged? The motor has permanently lubricated sealed ball bearings. To maintain the finish, clean with a soft, slightly damp cloth and buff with a dry cloth. Hunter Ceiling Fan Remote Not Working This video shows you the best way to clean and maintain your patio set.

If you still get no light coming on the remote after that, maybe it's time to replace the remote. It sounds like a bearing or brush problem in the motor. To tell if any of the blades are warped, you can use a blade balancing kit. useful reference View image here for details.

For more tips on troubleshooting ceiling fans or to shop the wide selection of fans and parts online, visit http://www.fandiego.com. I took the receiver out of the bell housing and had rewired the fan and lights to work manually. The first position is all off, the second the low speed coil, the third the medium speed coil, and the fourth both coils. If you have a pullchain, does that work?

It can cause corrosion and possible freezing damage in colder climates. Hopefully it works. My fan doesn't blow any air. To locate an exact replacement part for your specific ceiling fan model, you can search for your model or UPC number on www.homedepot.com and do the following: Select "Replacement Part List"

For information specific to your product, please refer to your instruction manual. The factory default is for all of the switches to be off. VideoJoeKnows 78,665 views 16:45 Hampton Bay UC7078T Up/Down Light (UC7078TUDL) Ceiling Fan Remote Control - Duration: 1:45. The UPC (12-digits) and/or model number can be found on the following: The product box Your Home Depot store receipt The user manual A sticker (usually silver) on the side of