Do you think it could be the switch?? I did just that and ended up melting the water line and the paddle dispenser. You might want to put a glob of dielectric paste where the wire enters each crimp connector to keep the water vapor out. AppliancePartsPros 165,773 views 7:34 Troubleshooting a GE water dispenser and installing a GE heater element - Duration: 58:13. this content
Reply Kelly July 12, 2013 at 6:11 pm I came home this afternoon after being out of the house for around 4 hours to find the refrigerator door applianceassistant 1,500,956 views 7:48 Top 6 Reasons Refrigerator Ice Maker Isn’t Working? — Refrigerator Troubleshooting - Duration: 3:46. Otherwise, you can leave the freezer door for a spell to warm it up and see what happens. If one of the dispenser switches is defective, the dispenser will not work.
Water Fill Tubes Start Your Repair Here We have fill tubes for thousands of models Search Need Help Finding Your Model Number? Removed coupler at bottom and water does not come out so assume frozen is not the issue. After a few days the display inside the frig portion would go out or flicker. Quick Question!
Still comes right back on. All rights reserved. Could the mother board be failing? Ge Under Counter Ice Maker In any case, let's assume that it is connected to the hot water line-From 11pm to 6am, no one uses the water dispenser, that's a 7-hour duration in which no one
Transcript The interactive transcript could not be loaded. Ge Refrigerator Ice Maker Not Getting Water Another technique is to empty everything from the unit, perhaps into an ice chest, and unplug it for a day. Reply The Handyguys June 2, 2014 at 1:21 pm Cool tip, thanks for sharing. http://www.geappliances.com/ge/service-and-support/refrigerators-freezers.htm If it's "open" it's shot.
This is a common problem. Ge Profile Refrigerator Ice Maker Problems French Door Use your smart phone to take a picture of the model number tag. Any ideas? Behind the cover is a series of electrical test points that can be used to diagnose the ice maker.
Top 6 Reasons Refrigerator Runs Constantly? check over here Hopefully one of these items you’ve checked wasn’t working because they’re all easy fixes. Ge Refrigerator Ice Maker On Off Switch The fix was to shut off power for 30 seconds. Ge Ice Maker Parts A simple fix is to warm it up for a bit.
I'm guessing you mean this thing; http://www.appliancepartspros.com/ge-trim-recs-bk-wr38x10314-ap3206652.html If that is what you're talking about, it simply pops off, there are three clips down the right side and three down the left news If there is rust around the wires that's probably the problem. Can't say exactly what might be wrong beyond what is in the video. Hope this helps. Ice Maker Not Making Ice Frigidaire
i had it set at 5 while away…tried it at 3 all day to see if that helped…it didn't. Replacing or installing a heater was more than I wanted to do. For me taking the light bulb out let's me get water again, but the led selection indicators fade a bit and I wonder if the power supplied to the door is http://sistemainmo.com/ice-maker/frigidaire-side-by-side-refrigerator-ice-maker-not-working.php Reply Wolf June 19, 2013 at 11:11 am I wonder, if replacing the bulb did fix your issues.
Or even a temporary fix tired of the 5am screaming match with an inanimate object Reply Tucker August 7, 2013 at 9:06 am My GE side by side Profile Model PSS2SHR Ge Bottom Freezer Refrigerator Ice Maker Problems Reply Charles Merlo April 28, 2013 at 9:06 am Absolutely positive1 Reply Bob Thomas May 1, 2013 at 11:06 pm It sounds to me as if you had an This valve is usually found under the sink or in the basement.
This feature is not available right now. Reply Jonathan Lackman June 10, 2016 at 7:44 pm Yeah, I had put the silver bubble wrap on the inside of the door. Reply The Handyguys December 27, 2012 at 9:42 am Thanks for the tips Bob - We agree that soldering the connections is more robust but not everyone possesses the tools or Ge Adora Refrigerator Ice Maker Troubleshooting At the end of the cycle, the icemaker module sends power to the water inlet valve to refill the tray with water.
Follow that line until you find where it connects to the plumbing. At any rate, you can replace the spring and flapper for very little and it's easy and described in this video; https://youtu.be/0xxyiDDDfwM Reply shari June 6, 2013 at 11:48 pm I heard of people gluing styrofoam on the inside of the door directly behind the dispenser. http://sistemainmo.com/ice-maker/ge-profile-side-by-side-refrigerator-ice-maker-not-working.php It then passes through a hose to a pan in the back of the unit where it evaporates.
If you use one of those clamp on saddle valves they are notorious for restricting flow. Use your smart phone to take a picture of the model number tag.